KNOWN ISSUE: Force calculations on interfaces and cut planes (Class 3 Error) |
SYMPTOM:<br>Forces at interfaces or cut planes are approximated by combining pressure and mass flow force contributions. However, this approximation will not balance the force on... |
KNOWN ISSUE: Transient multiphase flow with Total Energy heat transfer model (Class 3 Error) |
SYMPTOM:<br>When doing a transient multiphase simulation using the Total Energy heat transfer model, there is an error in the discretization of the transient pressure term in the energy... |
KNOWN ISSUE: CFD-Post may crash if an attempt is made to compute streamlines using the "Normal" variable |
SYMPTOM:<br>CFD-Post may crash if an attempt is made to compute streamlines using the "Normal" variable<br><br>PROBLEM:<br>The "Normal" variable... |
KNOWN ISSUE: MFX simulations may fail on HP-UX Itanium 64 platforms |
SYMPTOM:<br><br>When executing MFX (2-way FSI) simulations on HP-UX Itanium 64 platforms, the CFX-Solver may fail with an error such as:<br><br>An internal error has been... |
KNOWN ISSUE: Paths for projects and temporary files in ANSYS Workbench should not contain symbolic links |
SYMPTOM:<br>The problem shows up in various ways depending upon exactly which systems are being used and which paths contain symbolic links. For example, a system may fail to update due to... |
Q: In POLYFLOW - GAMBIT does not start under POLYMAN. What should be done? |
A: Here are some workarounds:<br><br>1. move/copy Gambit installation into ansys_inc/v140/polyflow in order to have a compatibility with FLUENT_INC definition;<br>2. in POLYMAN,... |
Q: In POLYFLOW there is a problem when asking the total extra-stress tensor for a film DCPP simulation case. What can be done? |
A: An easy workaround consists of not asking the extra-stress post-processor. The extra-stress post-processor is already activated by dafault; it is no longer needed to activate it a second time. |
KNOWN ISSUE: Not all turbo data saved in Turbo-Pre in certain circumstances (Class 3 Error if it were noit in Known Issues and Limitations document) |
SYMPTOM:<br>Some turbo-specific data may not be correctly set or written in Turbo-Pre mode.<br><br>PROBLEM:<br>Turbo data (Passages per Mesh etc.) previously defined by... |
KNOWN ISSUE: The CFX-Solver Manager in ANSYS Workbench crashes when starting the Command File Editor |
SYMPTOM:<br>Whenever the Command File Editor is invoked from the CFX-Solver Manager in ANSYS Workbench, the CFX- Solver Manager crashes.<br><br>PROBLEM:<br>This is due to a... |
KNOWN ISSUE: Radiation is not rotationally periodic (Class 3 Error) |
SYMPTOM:<br>When running cases with either the Monte Carlo or Discrete Transfer radiation model that have rotational periodicity, the CFX-Solver treats the periodic boundaries as symmetry... |
KNOWN ISSUE: Directional radiation sources can give incorrect answers in some circumstances (Class 3 Error) |
SYMPTOM:<br>The following combinations of directional radiation sources (available with the Monte Carlo Model) give incorrect answers with the current implementation:<br><br>- a... |
Q: In FLUENT: how can you replace an existing mesh with another similar one - is there an efficient way to retain the non-geometric parameters and models while substituting the mesh? |
A: The older FLUENT text user interface (tui) "file/reread-grid" functionality has been replaced in version 6.2 by the "grid/modify/replace-zone" functionality. this... |
Is there a way to import DesignModeler geometry in TGrid for meshing? |
Tgrid only reads faceted geometry.<br><br>If you have a geometry in DM, please connect the geometry cell with a mesh cell. Open the meshing application and allow the geometry to be... |
Q: My license file contains 2 INCREMENT lines for the ANSYS HPC Pack product (feature anshpc_pack), one for 2 tasks (allowing up to 32 cores for a parallel solver) and the other for 1 task (allowing up to 8 cores for a parallel solver).
|
A: This particular license file should give a pool of 40 cores which should allow a 24 core and an 8 core solver to be run at the same time with no problems regardless of the order in which the... |
Q: How can you do symmetric expansion about a local coordinate system? |
A: Please use following commands in command objects in workbench to expand over local coordinate system.<br>/post1<br>/show,png<br>/view,1,1,1,1<br>csys,14 !activate local... |
My programs won't start after installing on Windows 7. Are there any special installation requirements for Windows 7? |
The Windows 7 operating system has security controls that are set high by default. This will prevent successful installation.<br><br>In order to successfully install ANSYS products on... |
KNOWN ISSUE: Limitations with calculations of forces on Immersed Solids in CFD-Post (Class 3 Error if it were not mentioned in the Known Issues and Limitations document) |
PROBLEM:<br>CFD-Post does not include the viscous component of the force when calculating forces and torques on Immersed Solids.<br><br>WORKAROUND:<br>Use a monitor point... |
Is there a document for ANSYS 13.0 that covers installation, downloads,ANSYS Help, and technical support? |
Please see the attached pdf file. |
Are there any FAQs for ANSYS 13 that provide guidance on download, installation and setup, tutorials, etc.? |
<br>This FAQs document is available on the Customer Portal. Please navigate to Product Information -> ANSYS 13 -> FAQs.<br><br>This document contains a set of FAQs... |
KNOWN ISSUE: User specification of particle track limits gives incorrect export |
SYMPTOM:<br>If the User Specified value for Limits Option is used with a non-zero value for Start Time on the particle track object in CFD-Post, then, if the track is subsequently exported,... |
How can I collect ANSYS 13.0 licensing-related diagnostic log files on my Windows computer to attach to my Service Request? |
Download the attached command file ansys_debug130.cmd.<br><br>Double-click this file on the client machine and on the license server if applicable. It will output necessary information... |
KNOWN ISSUE: Custom files are not used when run started from Solver Manager |
SYMPTOM:<br>When cases that have been created in CFX-Pre and use custom files (e.g. RULES, VARIABLES) are started from the Solver Manager, the files are not used even though it is reported... |
KNOWN ISSUE: Error when a temperature dependent source is added to a 1:1 Fluid-Fluid interface |
SYMPTOM:<br>If a temperature-dependent source is added to a Fluid-Fluid interface whose Mesh Connection is set to 1:1, then the solver may generate the following messages during the... |
KNOWN ISSUE: Solver does not apply Fluid-Specific Velocity at wall (Class 3 Error) |
SYMPTOM:<br>If a Fluid-Specific Wall Velocity has been specified for an Eulerian multiphase calculation, then the CFX-Solver does not apply the velocities correctly to each phase. Instead,... |
Do you have a script (JScript) for v13 which converts one connection type to another? (Solution 2009435 does not work with v13.) |
/*<br> * Convert Connections<br> *<br> * This script converts connections from one type to<br> * another, based on the "toType" variable set below.<br>... |